- Home
- Oven keeps tripping
Oven keeps tripping the electrics? What it means and what to do.
Find out what tripped, check the cooker switch safely, and tell an appliance fault from a wiring fault. Backed by what we found on 57 real oven, hob and cooker jobs.

Oven, hob or the whole board: what tripped?
Open the fuse board and look at which switch is down. That tells you most of what you need to know. An RCD has a test button and protects a group of circuits. It trips when current leaks to earth. A breaker (MCB) protects one circuit. The cooker breaker trips on overload or a short.
| What you see | What it usually means | What to do |
|---|---|---|
| The RCD (switch with a test button) is down and several circuits are off | Current leaking to earth. Often the oven or hob, sometimes a damp or damaged cable or accessory | Cooker switch off, reset the RCD once. If it holds, the cooker is the likely cause |
| Only the breaker labelled cooker or oven is down | Overload or a short on the cooker circuit, or a breaker that is the wrong size for the cooker | Reset once. If it trips again, leave it off and call an electrician |
| Nothing has tripped but the oven is dead | Cooker switch off, the clock not set, a blown fuse in the plug or the cooker socket, or a failed element | Check the switch and the clock, then the plug fuse if it has one |
| Hob works, oven does not (or the other way round) | If both share one supply, usually the appliance that has stopped | Use the part that works, and get the other one checked |
| Cooker switch is warm, scorched, buzzing or smells of burning | A loose or overheating connection | Switch off at the fuse board and do not use it. See sparking sockets |
Zanussi says a tripping fuse “usually indicates an electrical or component fault”. It lists cable damage, water, faulty installation and overloaded circuits among the causes. More on RCDs in RCD keeps tripping.
The cooker isolator switch, and other safe checks
Most cookers and many built-in ovens and hobs are wired through a cooker switch: a large 45A double-pole switch on the wall near the cooker. Some have a 13A socket on the same plate; that is a cooker control unit. Turning it off cuts the cooker’s power without touching the rest of the kitchen. Do not take its cover off.
- Switch the cooker switch off, then reset the RCD or breaker once.
- If it trips again with the cooker off, the fault is somewhere else. Leave it and call an electrician.
- If it holds, switch the cooker back on. A trip now points to the cooker or its cable. Zanussi suggests a similar check: switch off as many other appliances as you can, restore the power, then turn the oven on.
- Note when it trips. At switch-on, or after 10 or 20 minutes of heating? Tell the engineer.
- Try the oven and the hob separately. If only one part trips it, that part is the likely cause.
- Oven dead but nothing tripped? AEG says many ovens will not work until the clock is set, so look for a flashing 12:00 or 00:00.
If the switch is warm, scorched or crackling, stop. Switch off at the fuse board and see sparking socket or burning smell.
The usual causes
A failed or damp element
Oven and hob elements wear out. When the insulation inside breaks down or takes on moisture, current leaks to earth and the RCD trips. It can trip at switch-on, or only once the element is hot. Either way the fix is a new element or a new appliance, not new wiring.
A loose terminal at the cooker switch or outlet plate
A cooker draws a heavy current for a long time, so a loose screw heats up. It can scorch the switch, damage the cable and trip the circuit. On 20 of our 57 jobs the fix was at the switch, outlet or spur: 14 where a part was replaced and 6 where the connections were checked and remade.
The wrong breaker
If a cooker sits on a breaker that is too small, it trips whenever the oven and hob are both on. In W11 and EN9 we found cookers on 6A and 10A breakers, with the lighting on 32A. The lighting was the bigger danger: a 32A breaker is far too big to protect a normal lighting cable. See does my fuse board need replacing?
A cracked hob or water getting in
Spills that reach the wiring through a cracked glass top or a missing seal cause earth leakage. Zanussi lists water as a cause. In N16 we found a hob with no rubber seal to keep water out, so we disconnected it and made it safe.
What we found on 57 oven, hob and cooker jobs
Our engineers attended repairs in Anchor sheltered housing for Axis Europe in 2025–26. In the records for July 2025 to September 2026, 57 jobs were about an oven, hob or cooker (cooker hood jobs left out). This is what each one came down to:
| What it came down to | Jobs |
|---|---|
| Oven or hob itself faulty: repaired, replaced, or left isolated for replacement | 20 |
| Cooker switch, control unit, outlet plate or fused spur replaced | 14 |
| Connections at the switch, outlet or spur checked and remade | 6 |
| Breaker, fuse, RCD or fuse board was the problem | 5 |
| Cooker connected, reconnected, moved or made safe, with no fault recorded | 8 |
| Working when we arrived: no fault found | 4 |
| Total | 57 |
In 11 of the 57 the notes say tripping. The oven or hob itself was at fault in 5. In 3 the cause was on the electrical side: a cooker on the wrong breaker, a faulty spur, and a cooker socket whose breaker had tripped and held once reset and the connections checked. In the other 3 it would not trip while we were there, though in one of those we replaced a cooker switch that was in bad condition.
Some of the jobs
| When | Area | What we found |
|---|---|---|
| August 2025 | SL1 | The oven circuit kept tripping. A faulty switched fuse spur was found and replaced, and the tripping stopped. |
| September 2025 | N16 | The oven tripped the RCD every time it was turned on. The cooker switch and its socket tested fine. The oven had an earth fault. |
| October 2025 | HA2 | One hob ring, the bottom right, tripped the RCD. The rest of the hob worked. The hob needed repairing. |
| October 2025 | E12 | Connections at the plate and hob tested fine, but the appliance tripped the board after 10 minutes of use. |
| October 2025 | EN9 | The cooker was on a 10A breaker and the lights on a 32A, with no RCD protection after a faulty RCD. We replaced the fuse board. |
| November 2025 | N16 | We upgraded the RCD from 63A to 80A, and the cooker worked again. |
| December 2025 | HA5 | The fuse in the cooker socket had no continuity. We replaced it and the cooker worked. |
| February 2026 | W11 | The cooker was on a 6A breaker and the lighting on a 32A. We swapped them over and the board stopped tripping. |
What it means for you: if the oven trips the RCD and the cooker switch tests fine, the appliance is the most likely cause. But 25 of the 57 jobs came down to the switch, a connection, a spur or the board, and those need an electrician. See our sheltered housing repairs.
Oven fuse: plug-in or cooker circuit?
Some built-in single ovens come with a 13A plug. NEFF says to use the plug if one is supplied, and to hardwire only ovens supplied with bare leads. It suggests testing the 13 amp plug fuse by swapping in one you know works. Such an oven is usually plugged into a socket or fused spur behind a switch. In SL1 the faulty part was a switched fuse spur.
Double ovens, range cookers and most hobs go on a cooker circuit: their own breaker, a cooker switch and an outlet plate, with no plug fuse. Beko says its split and cook oven needs a higher amperage circuit because it has two heating elements. Electrolux says most induction hobs cannot use a standard socket, and that all connections should be made by a qualified electrician.
A new cooker circuit counts as a new circuit, so it is notifiable under Approved Document P. Replacing a cooker switch or outlet is a replacement, which is not notifiable. Approved Document P still expects it to be designed, installed, inspected and tested to BS 7671.
Appliance or wiring: who to call
- Appliance engineer or the maker: it trips only when the oven or one hob ring is on, and the switch and circuit test fine. NEFF advises booking a repair if a working oven trips during use.
- Electrician: it trips with the cooker off, a new cooker trips before first use, the switch is scorched, or the breaker or RCD keeps going. Zanussi says a recent installation that trips could be an installation error. Not sure which? We test both in one visit.
Tenants: report it to your landlord. Section 11 of the Landlord and Tenant Act 1985 applies to most tenancies under seven years. It requires the landlord to keep the installations for the supply of electricity in repair and proper working order. That would normally include the wiring, the cooker switch and the outlet. It excludes appliances for making use of the supply. So whether the landlord replaces the cooker itself depends on your tenancy. Landlords, see electrical services for landlords.
How SEGplc can help
We test cooker circuits, switches and appliances for homeowners, landlords and housing providers across Hertfordshire and London. If the appliance is at fault we make it safe and tell you so, rather than rewire something that is fine. If the board is the problem, a new fuse board is from £399 inc VAT: see consumer unit replacement. We are an NICEIC Approved Contractor and TrustMark registered. For a kitchen fault we have found on an inspection, see the Chiswell Green extension, where loose connections were found at a kitchen appliance grid switch.
Questions about ovens tripping
Why does my oven trip the electrics as soon as I turn it on?
Usually because current is leaking to earth inside the oven, often through a failed or damp element, and the RCD cuts the power. In September 2025 we tested a cooker switch in N16 and found it fine: the oven itself had an earth fault and needed replacing. A loose connection or a faulty switch or spur can do the same, so it needs testing.
Why does my oven only trip after it has been on a while?
Faults that appear as the oven heats up are usually in the appliance. In October 2025 an appliance in E12 tripped the board after 10 minutes of use. The connections tested fine, so it needed replacing. NEFF’s advice is the same: if it trips during use, book a repair.
Can I keep resetting the RCD?
Reset it once. If it trips again straight away, or every time you use the oven, leave the cooker switch off and get it tested. AEG says to contact a qualified electrician if a breaker trips repeatedly.
Does an oven have a fuse?
A built-in single oven that comes with a plug has a 13 amp fuse in the plug, and NEFF suggests swapping it for one you know works. A cooker on its own circuit has no plug fuse: it is protected by the breaker in the fuse board, and some cooker switches have a fused socket too.
How do I know if it is the oven or the wiring?
Switch off the cooker switch and reset the board. If it holds, then trips when the cooker goes back on, the fault is in the cooker or its last length of cable. If it trips with the cooker switched off, the fault is elsewhere. An electrician can test both and tell you which.
I rent my home. Who should fix it?
Report it to your landlord. For most tenancies of under seven years, section 11 of the Landlord and Tenant Act 1985 says the landlord must keep the installations for the supply of electricity in repair. That would normally include the wiring, the cooker switch and the outlet. The law excludes appliances that use the supply, so who repairs the cooker itself depends on your tenancy.
Does a new cooker circuit need notifying?
Yes. Approved Document P lists a new circuit as notifiable work. Replacing a cooker switch is a replacement, so it is not notifiable, but it should still be installed, inspected and tested to BS 7671, the wiring regulations.
Sources
- Zanussi, Oven blows / trips fuses
- NEFF, Oven is not turning on
- NEFF, Can my oven be hardwired?
- AEG, Hob, oven or cooker won’t turn on
- Electrolux, How do I connect my electric ceramic or induction cooker to the power supply?
- Beko, Why does this appliance need a higher amperage electrical circuit?
- legislation.gov.uk, Landlord and Tenant Act 1985, section 11: repairing obligations
- legislation.gov.uk, Landlord and Tenant Act 1985, section 13: leases to which section 11 applies
- GOV.UK, Electrical safety: Approved Document P
- GOV.UK, Approved Document P, 2013 edition (paragraphs 2.5, 2.7 and 3.13)
Written by SEGplc, NICEIC Approved Contractor, SEG House, Chiswell Green, St Albans. Job figures from our repair records for Axis Europe, July 2025 to September 2026. Last updated 27 October 2026. This is general guidance: if you are not sure, leave the cooker switched off and call an electrician.
Need it done by a date?
Tell us the deadline. We’ll tell you honestly whether we can hit it — and we usually can.

