Open · 7 days, 7am–10pmHead office St Albans · Herts · Beds · Bucks · London
  1. Home
  2. Light bulbs keep blowing

Light bulbs keep blowing? Why it happens

One fitting or the whole house: the usual causes, what you can check, and when it needs an electrician.

LED lighting installed by SEGplc

Bulbs do fail, but if the same light keeps blowing them, or bulbs go all over the house, there’s usually a reason. Start by working out whether it’s one fitting or many.

Bulbs keep blowing in one light

Likely causeWhat you noticeWhat to do
Loose or worn lampholderBulb flickers when touched; scorch marks on the holderSwitch off and replace the lampholder or fitting
Bulb too powerful for the fittingEnclosed shades, spotlights in fire hoods, lots of heatUse the wattage on the fitting label; switch to LED
VibrationCeiling light under a busy floor or near a door that slamsUse LED bulbs, which cope better
Dimmer not matched to the bulbsLEDs buzz, flicker or fail earlyFit an LED-compatible (trailing-edge) dimmer
Halogen bulbs touched with bare fingersHalogen capsules or GU10s failing quicklyHandle with a cloth, or change to LED

Bulbs blowing all over the house

If bulbs fail in several rooms, the supply may be the cause. UK mains is 230 V, allowed to run between about 216 and 253 V. A supply at the high end shortens bulb life, and a loose connection at the fuse board or a shared neutral can make voltage swing. If lights also flicker or dim when appliances switch on, get it tested.

LED downlights failing

LEDs should last for years. When they don’t, it’s usually heat: an LED in an enclosed or insulated fitting not rated for it, or a cheap driver. Fire-rated downlights with integrated LEDs, matched to the right dimmer, solve most repeat failures.

When to call us

Call us if a lampholder is scorched, a fitting buzzes or smells hot, bulbs fail across the house, or a breaker trips when a bulb blows. See also lights not working.

We see these faults every week. Since summer 2025 our engineers have attended more than 2,700 repair call-outs in homes and flats across Herts, Beds, Bucks and London, around 630 of them for sockets and switches and over 900 for lighting.

Need an electrician in St Albans or Herts? Call 01727 238 999 or send us photos and a few details.
Want the wiring and fuse board checked? An EICR tests the condition of the installation: from £156 including VAT for a studio or one-bed flat with one fuse board. See what an EICR costs, or book an EICR in St Albans. For other work, see electricians in St Albans.

Questions we’re asked

Why do my light bulbs keep blowing in one light?

Usually a loose or worn lampholder, a bulb too powerful for the fitting, vibration, or a dimmer that doesn't suit the bulbs. Switch off and check the lampholder for scorch marks.

Why do bulbs blow all over my house?

If bulbs fail in several rooms, the supply voltage may be high or unstable, often from a loose connection. An electrician can measure it and check the fuse board connections.

Why does the breaker trip when a bulb blows?

When an old filament bulb fails it can briefly short inside, which trips the lighting breaker. Reset it once. If it keeps happening with LEDs, get the circuit checked.

Do LED bulbs blow less?

Yes. LEDs cope far better with vibration and switching and use less power. They do fail early if they get too hot, so use bulbs rated for enclosed fittings where needed.

Written by SEGplc. Last updated 19 November 2026.

Need it done by a date?

Tell us the deadline. We’ll tell you honestly whether we can hit it — and we usually can.

Contact

Talk to SEG

Questions about a job, a certificate or a programme of works? Call the office or send a message. Head office in St Albans, serving Herts, Beds, Bucks and London.

Emailhello@segplc.comPhone01727 238 999Also on0345 3 822 833OfficeSEG House, 192 Watford Road, Chiswell Green, St Albans, Herts AL2 3EBHours7 days, 7am–10pm · call-outs every dayLeadershipMichael Simm · Russell Solts
Call nowGet a quote