Open · 7 days, 7am–10pmHead office St Albans · Herts · Beds · Bucks · London
  1. Home
  2. Sump pump wiring

Wiring for sump pumps, basement pumps and treatment plants.

Tanking a basement, fitting a sump pump or installing a sewage treatment plant? We wire the pumps, alarms and controls, and certify the work. Based in St Albans.

New labelled consumer unit in a St Albans house

A pump is only as reliable as its electrical supply. If it shares a circuit with other things and that circuit trips, the pump stops, and you usually find out when the water arrives. We wire pumps so that cannot happen quietly.

What we wire

  • Sump pumps in tanked and waterproofed basements and cellars, single or twin.
  • High-water alarms and battery back-up units.
  • Sewage treatment plants and pumping stations for homes that are not on mains drainage.
  • Lift sump pumps and water booster sets in blocks of flats.
  • The rest of the room: ventilation fans, sockets and lighting, done on the same visits.

Electrics for a tanked basement

Most basement waterproofing uses a membrane that sends any water to a sump, where a pump lifts it out to a drain. The waterproofing company supplies the pump station. An electrician connects it. This is what we do:

  1. A dedicated circuit for the pump from the fuse board, with its own protection, so a fault on another circuit cannot switch the pump off. Twin pumps are wired the way the maker asks, often one circuit each.
  2. A local isolator beside the pump station, so it can be serviced safely.
  3. The high-water alarm connected and tested.
  4. Battery back-up connected, where one is supplied, so the pump keeps running in a power cut.
  5. Cable routes agreed with the waterproofing company first. A screw through the membrane is a leak, so fixings go where they say.
  6. The ventilation fan wired with its own control, usually a humidistat or a run-on timer.
  7. Sockets and lighting. New sockets where you want them, and downlights in place of a single ceiling light.
  8. Tested and certified. You get an Electrical Installation Certificate, and we notify the work to building control under Part P.

Timing. It is normally two visits. First fix, when the cables go in, is after the membrane is on and before the walls are boarded. Second fix is after plastering, once the pump station is in. Call us before the work starts and we will fit around the waterproofing company’s dates.

Is the fuse board up to it? New circuits need spare ways and RCD protection. If your board is full or old we will say so before we quote. See consumer unit replacement.

New consumer unit with every circuit labelled
A new fuse board we fitted, with every circuit labelled.

Sewage treatment plants and pumping stations

A packaged treatment plant needs a permanent supply for its motor or air blower, and often a pump and an alarm as well. We run the supply from the house, usually in armoured cable underground, fit an isolator at the unit, connect the alarm, and wire the plant to the maker’s diagram. Then it is tested and certified like any other new circuit.

Pump work from our own records

Customers are not named.

  • A private property on the edge of St Albans. Treatment plants wired by our engineer Tom.
  • Luton. Another wired by Tom.
  • A house project, November 2020. A second sump pump connected as part of the electrical installation.
  • Blocks of flats in Upper Edmonton, north London, February 2022. Tom surveyed the lift sump pumps and the water booster sets before new containment went in. The stairwell pump was fed from a 6A breaker through a direct-on-line starter and the booster set from a 32A switch-fuse. An old mineral-insulated cable into the lift shaft crossed the new route, so it was flagged for rewiring.

What to send us for a quote

  • The make and model of the pump station or treatment plant, or the installer’s specification sheet.
  • How many pumps, and whether there is an alarm and a battery back-up.
  • A photo of your fuse board with the cover open, and roughly how far it is from the pump.
  • Anything else you want done at the same time: fan, sockets, lighting.
  • The date the waterproofing or drainage work starts.
Having a basement tanked, or a pump or treatment plant fitted? Tell us what is going in and when: request a quote or call 01727 238 999.

Questions we’re asked

Does a sump pump need its own circuit?

It is what we fit. The pump gets its own protected circuit from the fuse board, so a fault somewhere else in the house cannot switch it off. Check the maker's instructions too, as most ask for a dedicated supply.

Can a sump pump just be plugged into a socket?

Some small pumps come with a plug. For a basement that relies on the pump, we recommend a fixed connection on its own circuit with a high-water alarm, so it cannot be unplugged by mistake or tripped by another appliance.

What happens to the pump in a power cut?

It stops unless there is a battery back-up. Many basement pump stations can be supplied with one, and we connect it. Ask your waterproofing company which they recommend.

Do you supply the pump or the treatment plant?

Normally the waterproofing or drainage company supplies it and we wire it. We work to the maker's wiring diagram.

Will I get a certificate?

Yes. A new circuit comes with an Electrical Installation Certificate, and we notify the work to building control under Part P.

Can you do the fan, sockets and lights at the same time?

Yes. It is cheaper to do it in the same two visits as the pump wiring than to come back after the basement is finished.

Which areas do you cover?

St Albans, Harpenden, Luton, Watford and the rest of Hertfordshire and Bedfordshire, and north London. Our office is in St Albans.

Written by SEGplc from our own job records. Last updated 13 November 2026.

Need it done by a date?

Tell us the deadline. We’ll tell you honestly whether we can hit it — and we usually can.

Contact

Talk to SEG

Questions about a job, a certificate or a programme of works? Call the office or send a message. Head office in St Albans, serving Herts, Beds, Bucks and London.

Emailhello@segplc.comPhone01727 238 999Also on0345 3 822 833OfficeSEG House, 192 Watford Road, Chiswell Green, St Albans, Herts AL2 3EBHours7 days, 7am–10pm · call-outs every dayLeadershipMichael Simm · Russell Solts
Call nowGet a quote